Skip to content

Ways to Propagate Raspberries

Propagating Raspberries

A few weeks ago, I decided to start a hobby backyard nursery with my three daughters. I was inspired by the SideHustle Podcast, started watching Youtube videos to educate myself and quickly became addicted to the idea of propagating plants. 

That might sound a bit strange to you—then again—maybe not, because you apparently were searching for similar information on the web. 

I’ve always had an affinity to caring for and growing ‘things’. My primary hobby/escaspe is caring for saltwater fish and corals in an aquarium and propagating corals. After you’re done reading this article, check out my other obsession—it’s as addictive as propagating plants and a similar hobby. You’ll see I have a 15 year head start over there.

I’ve had a few plants that I’ve cared for and nurtured over the years, but I had never taken plant propagation all that seriously. 

In my research, I had come across a few different propagation techniques:

  1. Division (which is how I propagated my very first plant—the Hostas on the side of my house)
  2. Semi-softwood cuttings (which is how I propagated the gigantic, overgrown hydrangea in my front landscape bed
  3. Layering 

I have a bed of raspberries in my garden, so I searched YouTube for the best way to propagate the raspberry plants. With my initial searches, I found plenty of instructions about how to propagate raspberries, but eat video just showed how that person did it, and everyone seemed to have a slightly different approach. 

I learned that some people propagate raspberries by digging them up, while dormant, and moving them to their new/preferred/desired location. A few people showed how they dug up suckers during the growing season.

Others propagated them right out of the container they were purchased in. Some people used layering to propagate black raspberries.

But which is the best? I don’t want to dedicate a few years to exhaustively prove this point, but I did figure that I could do a quick experiment, with a small sample size, and see what happens.

1. Propagation by transplanting raspberries

Digging up raspberries is a fairly straightforward affair. You identify the cane you want to transplant and you dig straight down, a few inches away from the base of that cane with the shovel and start to remove the dirt around the root ball. As you get closer to identifying where there roots are, you may want too witch away from your shovel and use those two, 5-fingered shovels you were born with, so that you don’t do unnecessary damage to the roots.

Once you find the roots, you will notice that the cane you are tying to remove is attached to the other canes by a single ticker root. You have to sever that attachment before you will be able to remove your cane. 

Your goal is to try to get “a nice amount” of roots with your cane. 

Place the cane and roots in a gallon pot or dig a hole in the ground where you want to expand your berry patch. 

When is the best time to dig up and transplant raspberry plants?

The best time to dig up and transplant raspberry plants is just about any day you have a few minutes free when you can dig up and transplant a raspberry plant where you aren’t experiencing  the harshest weather in your climate—meaning you probably want to avoid the hottest, coldest, snowiest or rainiest days, but there are a whole lot of good days in between.

In Winter or early spring, while the plants are dormant

A pretty solid argument could be made that the best time to dig up a raspberry cane is while the plant is dormant. After the first heavy frost and before the cold breaks in the spring time is a period of time when raspberry plants are dormant—similar to hibernating for the winter.

Theoretically, transplanting your raspberries during this time could be perfect, because the plant essentially ‘sleeps through the procedure’ and then ‘wakes up’ none the worse for wear when the weather warms up in the spring. There is very little stress to the plant during this phase and it likely minimizes damage to the plant. 

Propagating your raspberries from dormant plant material may be slightly more complicated if you did not prune back the dead wooded at the end of the season. Since all of the plant material at this point in the year is either dead or dormant, it will be a bit easier to mistake last year’s flurocaine for a primocaine. 

In Summer or early fall, after fruit is harvested. 

A reasonable case ould be made that the late summer and early fall, after all the fruit has been harvested ould be theist time of year to dig up and transplant raspberries.

At this time of year, the visual differences between the succulent growth that will survive the winter and the woody growth about to die is most apparent, so you can most easily select the best canes and suckers for digging up.

The biggest challenge when digging up at this time of year is allowing the plant to recover from the trauma. A freshly dug up cane will droop immediately after relocation and needs to be allowed time to recover out of the hot sun.

Mid-to-late Spring, when fresh growth emerges

It’s probably hard to make a case that the early spring is the best time to dig up and transplant raspberry plants—unless your plan is to dig up the suckers growing up and underneath larger canes that you intend to be the primary fruit providers in that spot. 

When that is the case, identifying those young suckers and digging them out might actually be the perfect time because you put that succulent growth that’s trying so hard to make it in this world in the perfect place to grow up. Cutting back the mother plant in this fashion will also encourage more growth which will yield other fruiting canes, or canes you can further sub-divide.

2. Large cane cuttings

Another popular method of propagating raspberry plants involves clipping an entire cane at the base, just above the soil in late summer or early fall.

Based on the information I found online, there does not appear to be any consensus about whether leaves should be left on, or off, whether rooting hormone is useful, or not, and whether you should just bury the cane ‘as is’ or strip off the outer layer of tissue. 

During my first propagation of these raspberry plants, I set out to experiment with all three methods, like the bear going over the mountain, to see what I could see. 

Common steps for all large cane cuttings

Each of the large cane cutting methods employs a few similar steps. A cane is selected from the raspberry patch and is cut, close to the ground. Depending on the length of cane and number of leaf nodes, a few cuttings of 6 to 12 inches are made so that at least one node is buried below the dirt, to form roots, while at least one other node is above the dirt.

Variations on Leaf cutting


There are at least three different ways to treat the leaves, you can leave them all on, remove them all, or leave just a few on—either just the top one or two, to as many as the top 20%, or one fifth of the leaves.

Proponents of leaving the leaves advocate for the important role leaves play in nourishing the plant, turning sunlight and water into life-sustaining sugar.

Proponents of leaf removal highlight that “plant” isn’t really a plant, when first cut, it is a stem that is unable to sustain leaves. Cuttings also “sweat” out of leaves,Plants also sweat (transpire) out of leaves. Leaving leaves on a cutting wicks some of the moisture right out of the plant and soil, creating risk that the cutting will dry out.

Those of us unwilling to join one side or the other completely may wish to leave just a small amount of leaf or leaves at the very top of the plant—the newest, freshest growth, to serve as small solar panels that generate just a humble amount of sugar.

Which method works best for rooting raspberries? That’s what I set out to determine.

Leaving the leaves on

I left the leaves on a couple of canes—which was a short-lived and visually unsuccessful experiment. Within a few days, the leaves on those canes withered up, almost completely. Each cane retained a small amount of living leaf tissue, but the vast majority yellowed,burned, or dried up. 

At 24 hours, they looked great

By 7 days, the leaves were ~50-60% damaged.

By 14 days, the leaves were 80+% damaged.

These canes, with the original leaves left on, were also the slowest to create new buds, with no visible budding 14 days after the initial cutting/propagation.

Trimming back all but the top leaves

Trimming back all but the top, very small leaves, appeared to work right from the start. The original leaves survived and the plant put out new leaves from the top center, within14 days later.

Removing all the leaves, scraping the bottom and using rooting hormone

The technique that seemed to provide the fastest results throughout the cane was the method where I removed all the leaves from the canes and scraped the outer layer of tissue away before dipping in the rooting hormone.

3 of 4 of these canes showed new leaf growth, as well as multiple swelling buds on day 14, eclipsing the amount of leaf area (approximated with visual inspection), and having the best looking buds throughout the cane.

Simply removing the leaves without cutting/stripping away the outer tissue layers before planting produced swollen buds by day 14, but no leaves.

Locate the cane you want to propagate and use garden sheers or a knife to make a clean cut just above the dirt.

Trim the bottom with a cut so that only a minimal amount of cane remains below the lowest leaf node.

Remove the leaves from all the nodes except for the two leaves at the top node. 

You can leave the top leaves attached to the stem, but will want to cut-back the leaves, removing ~75-80% of the leave, leaving only 20-25% of the leaf material attached to the stalk. 

Some people report success removing all the leaves entire. 

Bury the crane in the center of a pot filled with pre-soaked potting soil and set it in a shady location. After a few weeks, the plant will set root and sprout new leaves.

Allow the cane to regrow through the winter and transplant it next Spring.

A variation on this method involves stripping outer layer of the bark from the cane at the bottom two nodes and dipping that part of the plant in rooting hormone before pushing it into the container.

About one month later, the only difference was that the leaves that were left on the stem or that budded from the aggressively treated canes grew a bit larger, but there was not much else above ground to note.

Now it is also worthy of noting that all of the canes from that initial experiment were left out in the open air. The soil was watered, to keep things moist, but the leaves had to deal with the harsh heat and dry air of early September.

Compare that to the image below from a bunch of canes that were cut, all with their leaves on–with some aggressive treatment of the cane (scraped with a knife). A few of the canes were too large for a lid, so the tote was sealed up with a white kitchen trash bag.

After just a few weeks, there was significant budding on several of the canes and most canes retrained the majority of their leaves.

3. Multiple cuttings from each raspberry cane

I was curious to find out if I could make more than one baby plant from a single cane, the same way I learned to propagate hydrangeas.

When propagating hydrangeas, you can make a new plant from essentially every two-leaf nodes.

I haven’t seen any videos where someone propagated a hydrangea using the whole branch, like they do with the raspberry canes. It seems likely that it would be positive, however. So that’s what I set out to do here.

I cut a few healthy raspberry canes in the late summer that were bunched up and growing a bit too closely with a neighboring cane.

I then divided each cane into two node sections.

For half of the cuttings, I removed all leaves. For the others, I simply trimmed the leaves back by 80%.

Within each of those respective groups, I cut away the bark in some and left the bark on for others. I also dipped all canes in rooting hormone.

I clearly should have labelled my cuttings/experiment better–but what I can confirm from the multiple cuttings experiment is that you can propagate raspberries from double-node pieces, just like hydrangea and mulberries.

I also observed different rates of leafy growth from different stem pieces–so I do suspect that the relative treatment (leaves/no leaves cut bark or not) does play a role, to be more effectively explored later.

4. Dividing raspberry plants

Dividing up raspberry plants is something you  can do if you dig up (or un-pot) a plant and see that there are multiple canes growing—or if you see little suckers (baby plants) shooting up.

Dividing up plants is a game of fractions. Your goal is to cut the roots proportionately with the size of the plant material you’re working with. If you have two evenly spaced out canes, a great place to start is right down the middle. 

If you have a cane you want to separate out that looks to be the dominant structure in a quarter of the container or root ball, cut straight down where it looks like the ‘fair’ border is between it and its neighbors.

This is not an exact science other than what you need to do is get the cane and as much reasonable root material directly underneath it that you can, ripping some, but as little of the roots as you can manage and then transplanting the cane with roots to the area you want to grow it out. 

Watch this video to learn more about dividing Raspberries and see the technique in action.

5. Layering


The last method you could use to propagate raspberry plants is called layering. What I love about layering is that the cane remains attached to the root system and mother plant the entire time, until an adequate root system is created. In this way, losses and stress can be minimized.

Layering is a technique that leverages the plant’s natural tendency to put down roots wherever it comes into contact with the dirt.

If you have a low-lying cane, or a sucker that is growing out diagonally or sideways, out from under the shadow of a larger cane, you can encourage further propagation by laying that cane down along the ground and covering parts, or all of it with dirt. 

You may need to heap the dirt or add a small stone to provide enough weight to keep the cane in contact with the dirt. As long as it bends but doesn’t break, your moment or two of effort should be rewarded with more raspberry canes growing up from that original sucker.

Depending on the type of raspberry plant you have, the relative height of the cane and how bendable it is, you may also be able to bend the cane over and stick the tip right into the dirt (or pot filled with potting soil/dirt).

The tip should also root and send up new growth. Several days after you see the new growth, give a gentle tug on the stalk to confirm it is rooted (and doesn’t pull immediately back out of the dirt). Once you’re sure it has roots, just cut the stalk and enjoy your new plant.

Last but not least is a technique called air layering. With this technique, what you do is expose an area of the cane that can’t naturally reach the dirt (too high up, or cane too stiff) to dirt by surrounding that portion of the cane with dirt, triggering the same rooting response further up the cane where dirt wouldn’t otherwise be able to be reached. 

Most people also either cut slits in the part of the cane that gets covered with the dirt, to create a wound, scar tissue and expose the inside of the plant to the soil, or even cut a ring the outer tissue away.

Cutting away the tissue should encourage/accelerate root growth, but it also creates an opportunity to damage the plant as well.

Air layering

Air layering is a technique that is similar to ‘regular’ layering, except that you expose branches (or canes, in this case) to dirt that are in the air—NOT on the ground or otherwise easily in touch with the dirt. 

You can do it on a lean budget with plastic bags and ties, like in the image below (not a raspberry, sorry):

air layering propagation technique

There also are small gizmos (that’s a propagation technical term, I learned it in imaginary propagation technical school) you can use to help you keep the dirt in contact with the branch/cane.

The most popular method involves removing the outer layer of the plant in a small ring that will be in contact with the dirt. When done correctly, this allows water from the roots to reach the tip of the branch/cane, but interrupts the flow of sugars from the leaves back down to the roots.

Those sugars concentrate around the ring of wounds and fuel root-growth.

The advantage of air layering is that you create the new rooting system while the top of the cane remains intact with the rest of the plant and only cut and remove it once the roots are mature, essentially eliminating any risk of killing the cutting.

In this way, you could create two, strongly rooted raspberry clones from each cane—one bare root that you could dig out over winter, and one clone of the top ‘half’ of the cane that you could cut once the root ball is fully formed.

But this technique seems to make a bit more sense when used to propagate delicate plants that don’t propagate well with cuttings, or those with lateral branches where you want to keep the main plant intact.

Leaf/branch(experiment)

While propagating raspberries and blackberries via layering (encouraging a low-growing cane to contact with the dirt, in a pot, as it grows out horizontally—see above), I noticed something interesting that spurred another propagation idea/technique.

When a cane grows horizontally instead of vertically, a few of the side branches, which would otherwise look like unassuming branches acting like natural solar panels for the plant, were growing quite vigorously and looked more like miniature canes than inconsequential branches. 

Some of the branches even have two small green tendrils that hang down that look a bit like roots or some structure intended to help grab hold.

Then the idea hit me like a lightning bolt. Eureka! If layering a cane sideways would encourage the plant to turn side branches into new vertically growing canes, maybe the branches themselves could be successfully propagated too, and turned into new plants themselves.

Up until this point those branches, and the leaves, were simply collateral damage—I like to call it ‘the carnage’ that is left over, to be thrown into the compost heap.

Because I was short on time + space/containers and flush with canes, I jammed as many of the branch and leaf sections as I could using a method similar to the bulk-production of arbor vitae and hydrangeas — an inch or two a part in a single flat container. 

I pre-hydrated the potting mix. I did not use any rooting hormone. I used a lid on the container to help retain moisture.

You can see the ‘results’ in the image below:

You can see that the container was packed fairly tight with leaves–and a few notes on what you see above. The leaves were already showing significant signs of caterpillar and beetle damage before being placed in the tote, but I found a few caterpillars on the inside chomping away. Oops.

But you can also see a whole lot of dead material. The tote got and stayed too wet–not enough drainage.

After clearing out the dead leaves and stems (mostly), it looked like this.

A few of the branches appear to have rooted–when you tug on them, they don’t want to come up. There were a few questionable stems that looked dead that I pulled up with some very minor roots.

Autumn is here–the last few days have been in the 40s/50s (F), I fear these tiny transplants may not make it all the way, but they certainly suggest that raspberries can potentially be propagated from branch/leaf cuttings.

Conclusions

In a relative short period of time during the last weeks of Summer and first weeks of Autumn, I demonstrated early propagation success with large raspberry cane cuttings (about 6-8 inches), small cuttings (2 small nodes), and from lateral branches.

The small cuttings produced very small leaves–they seem like they will become much smaller plants than their larger-caned cousins.

The branches were the least vigorous of all.

In a small head-to-head comparison of three methodologies: removing all leaves and scraping the outer layer off the bottom node, removing all leaves but the top 1-2 (and not scraping bottom), and just cutting and sticking the canes in the dirt (all 3 in open air), the aggressive method appeared to have the most leaf growth through one month. The canes with all the leaves wilted back and lost all leaves, while the canes with top leaves retained them throughout, although not much other growth was observed.

In a follow up set of propagations of many canes, leaving the top leaves and scraping the bottom, all canes were kept in a humidity dome (white trash bag that was tight-fitting over the top). After a few weeks, all canes retained large, healthy growth and also showed significant new budding (size of budding larger than in the first experiment).

Discussion and future experiments/next steps

These experiments were a bit more haphazard, based on the availability of my time…and pruned back canes. Three variables did appear to have a positive impact on growth of leaves – 1) scraping the outer layer of the bottom of the canes, 2) humidity dome, 3) removing most or all of the leaves.

In future experiments I intend to control for these variables a bit more closely and in head-to-head comparisons.

I’ll track the growth of these plants through the winter and update next Spring. I’m curious to see if the growth rates are significantly different across individual plants.

Have you tried to propagate your raspberry plants? What is your preferred technique? Was it successful? Please leave a comment below.

Leave a Reply

Your email address will not be published. Required fields are marked *